环境规制对技术创新的影响研究

本文选取了我国2005—2017年30个省份的面板数据,运用Sys-GMM估计法测度了环境规制强度及其异质性对技术创新的影响效应。结果表明:环境规制强度对技术创新有着先促进后抑制的作用;异质性方面,命令控制型、市场激励型、公众参与型环境规制对技术创新的影响也都具有先促进后抑制的作用,公众参与型规制对技术创新的促进作用最明显,市场激励型次之,命令控制型最弱。此外,本文通过构建门槛模型,研究发现环境规制对技术创新的影响具有门槛效应。     

Effect of bristle pack position on the rotordynamic characteristics of brush-labyrinth seals at various operating conditions

Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.     

A multi-stage regulation strategy of space manipulators with a free-swinging joint failure

To ensure tasks can be completed after a free-swinging joint failure occurs, a multi-stage regulation strategy of space manipulators is proposed. Considering all terms of the dynamics equation, an evaluation model of the regulation ability (EMRA) of active joints over the fault joint is established based on the fuzzy entropy. And then a multi-stage regulation strategy based on the EMRA is designed to regulate the fault joint. The strategy divides the regulation process into several stages, and select a certain active joint to regulative the fault joint in every stage. With this multi-stage regulation strategy, the fault joint can be regulated to the desired angle without huge torque on regulative joints. The simulation is carried out with a 7-DOF space manipulator, verifying the correctness and effectiveness of the multi-stage regulation strategy. The strategy has three advantages: Coriolis and centrifugal terms are both considered for the first time in selecting the regulative joint, making the selection result more in line with the actual regulation process; The influence of the model uncertainty is eliminated in establishing the EMRA, making the evaluation of regulative ability more precise; The fault joint is successfully regulated to the desired angle without huge torque on regulative joints.     

某机载探测系统自主回收技术的实现

针对某机载探测系统探头回收自动化程度低的问题，提出了在无需操作员干预情况下实现探头自主回收的技术方法。采用了先进的控制算法，将缆位角与探头、缆长进行结合并引入了绞车控制系统，使绞车对探头的回收速度及缆长可进行实时调整，并给出了3种不同缆位角摆动条件下缆长与探头回收速度的控制曲线关系。研发了自主回收装置，设计了能够实现自主回收功能的探头回收机构。实验验证表明：在无需人为干预的条件下，在缆位控制系统及自主回收机构的配合下，系统实现了对探头快速、安全的回收。     

H5飞机调油方法研究

对Ｈ５飞机经过了计算、论证、试飞，在此基础上提出了一种既安全又能充分发挥飞机飞行性能，同时又使动作程序化的调油方法－－规划调油法。用这种调油就可以大大地减少飞行员操纵飞机进的注意力分散，更利于集中精力操纵飞机，以保证飞行的安全。     

用两端安装法检定热电偶

利用一种设计好的专用检具 ,使两束被检热电偶分别从检定炉的两端安装均可保证符合检定规程的要求 ,从而在不添置新设备的情况下 ,使检定热电偶效率大大提高。     

利用热源温度场迭加法诊断持续点热源的强度及位置

可重复使用运载器的防热瓦故障会使航天器的局部结构产牛热源，并在结构中形成温度场。应用热源温度场迭加法的解函数，解得结构温度历程，然后据此温度的变化率趋势判断出热源位置，在此基础上依据多点测最值构造出辨识参数用于热强度识别，通过对一薄壁结构模型算例的计算仿真，证明了本文所提方法的有效性。论文工作为进一步开展热源诊断技术研究，提供了可资工程实践应用的数值算法体系以及有益的数值计算结论。     

关于危险品运输的紧急救援

危险品运输是技术要求最高的一类特种货物运输。在运输、装卸及贮存保管过程中,稍有不慎便会发生事故,造成人身伤亡和财产毁损。笔者认为:灾害=事故十损失。严格执行危险品运输规章,减少事故发生率,从技术上进行要求。仅是问题的一个方面。而另一方面还应立足于事故发生后的紧急救援,以最大限度地减少损失,两者并重才不致酿成灾害。为此,提出了建立“危险品运输紧急救援中心”的建议。     

钣金制件表面的相贯线求作方法

本文提出钣金制件表面相贯线求作的新方法。     

全位置自动焊管机TIG焊电源研制

本文介绍了一种适用于管－管、管－板对接的全位置自动TIG焊晶体管电源，该电源采用可编程控制器控制，具有直流／脉冲功能，焊接参数在4个区间内可分别预测，试验表明，该电源区间过渡时电弧稳定，抗干扰能力强，焊缝均匀、连接。